View TS256MSDM_4791729.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

TS128M~2GSDM
Description
Transcend miniSD Card is non-volatile, which means no external power is required to retain the information stored on it. Besides, it is also a solid-state device that without moving parts to skip or break down. Transcend miniSD Card can offer an incredible combination of fast data transfer, great flexibility, excellent security and incredibly small size.
miniSD Memory Card Features
* ROHS compliant product * Operating Voltage: 2.7 ~ 3.6V * Operating Temperature: -25 ~ 85C * Insertion/removal durability: 10,000 cycles * Fully compatible with SD card spec. v1.1 * Comply with SD Association File System Specification * Forward compatibility to MultiMediaCard Version 2.11 * Supports Copy Protection for Recorded Media(CPRM) for music and other commercial media * Form Factor: 21.5mm x 20mm x 1.4mm
Placement
9 1 2 3 10 11 4 5 6 7 8
Pin Definition
2GB
Front
Back
Pin Name Type Description No. 1 CD/DAT3 I/O/PP3 Card Detect/Data Line [Bit3] 2 3 4 5 6 7 8 9 10 11
CMD VSS1 VDD CLK VSS2 DAT0 DAT1 DAT2 NC4 NC4 PP S S I S Command/Response Supply voltage ground Supply voltage Clock Supply voltage ground
I/O/PP Data Line [Bit0] I/O/PP Data Line [Bit1] I/O/PP Data Line [Bit2] I/O/PP For Future Use I/O/PP For Future Use
Transcend Information Inc.
1
TS128M~2GSDM
Architecture
miniSD Memory Card
Transcend Information Inc.
2
TS128M~2GSDM
Bus Operating Conditions * General
Parameter
Peak voltage on all lines All Inputs Input Leakage Current All Outputs Output Leakage Current -10 10 A -10 10 A
miniSD Memory Card
Symbol
Min.
-0.3
Max.
VDD+0.3
Unit
V
Remark
* Power Supply Voltage
Parameter
Supply voltage Supply voltage specified in OCR register Supply voltage differentials (VSS1, VSS2) Power up time -0.3 0.3 250 V ms From 0v to VDD Min.
Symbol
VDD
Min.
2.0
Max.
3.6
Unit
V
Remark
CMD0, 15,55,ACMD41 commands Except CMD0, 15,55, ACMD41 commands
Note. The current consumption of any card during the power-up procedure must not exceed 10 mA.
* Bus Signal Line Load
The total capacitance CL the CLK line of the SD Memory Card bus is the sum of the bus master capacitance CHOST, the bus capacitance CBUS itself and the capacitance CCARD of each card connected to this line: CL = CHOST + CBUS + *CCARD Where N is the number of connected cards. Requiring the sum of the host and bus capacitances not to exceed 30 pF for up to 10 cards, and 40 pF for up to 30 cards, the following values must not be exceeded:
Parameter
Bus signal line capacitance Single card capacitance Maximum signal line inductance Pull-up resistance inside card (pin1)
Symbol
CL CCARD RDAT3
Min.
Max.
100 10 16
Unit
pF pF nH K
Remark
fPP 20 MHz, 7 cards fPP 20 MHz May be used for card detection
10
90
Note that the total capacitance of CMD and DAT lines will be consist of CHOST, CBUS and one CCARD only since they are connected separately to the SD Memory Card host.
Parameter
Pull-up resistance Bus signal line capacitance
Symbol
RCMD, RDAT CL
Min.
10
Max.
100 250
Unit
K pF
Remark
To prevent bus floating fPP 5 MHz, 21 cards
Transcend Information Inc.
3
TS128M~2GSDM
* Bus Signal Levels
miniSD Memory Card
As the bus can be supplied with a variable supply voltage, all signal levels are related to the supply voltage.
To meet the requirements of the JEDEC specification JESD8-1A, the card input and output voltages shall be within the following specified ranges for any VDD of the allowed voltage range:
Parameter
Output HIGH voltage Output LOW voltage Input HIGH voltage Input LOW voltage
Symbol
VOH VOL VIH VIL
Min.
0.75* VDD
Max.
0.125* VDD
Unit
V V V V
Remark
IOH = -100 A @VDD min IOL = 100 A @VDD min
0.625* VDD VSS - 0.3
VDD + 0.3 0.25* VDD
Transcend Information Inc.
4
TS128M~2GSDM
* Bus Timing
miniSD Memory Card
Parameter
Clock frequency Data Transfer Mode Clock frequency Identification Mode (The low freq. is required for MultiMediaCard compatibility.) Clock low time Clock high time Clock rise time Clock fall time Inputs CMD, DAT (referenced to CLK) Input set-up time Input hold time Outputs CMD, DAT (referenced to CLK) Output Delay time
Symbol
fPP fOD
Min
0 0
Max.
25 400
Unit
MHz KHz
Remark
CL 100 pF, (7 cards) CL 250 pF, (21 cards)
Clock CLK (All values are referred to min (VIH) and max (VIL)
tWL tWH tTLH tTHL
10 50 10 50 10 50 10 50
ns ns ns ns ns ns ns ns ns ns 14 ns
CL 100 pF, (7 cards) CL 250 pF, (21 cards) CL 100 pF, (7 cards) CL 250 pF, (21 cards) CL 100 pF, (7 cards) CL 250 pF, (21 cards) CL 100 pF, (7 cards) CL 250 pF, (21 cards) CL 25 pF, (1 cards) CL 25 pF, (1 cards) CL 25 pF, (1 cards)
tISU tIH tODLY 5
5 5 0
Transcend Information Inc.
TS128M~2GSDM
Reliability and Durability
Temperature Operation: -25C / 85C (Target spec) Storage: -40C (168h) / 85C (500h) Junction temperature: max. 95C
miniSD Memory Card
Moisture and corrosion
Operation: 25C / 95% rel. humidity Storage: 40C / 93% rel. hum./500h Salt Water Spray: 3% NaCl/35C; 24h acc. MIL STD Method 1009 10.000 mating cycles; test procedure: tbd. 10N 0.15N.m or +/- 2.5deg 1.5m free fall UV: 254nm, 15Ws/cm according to ISO 7816-1 No warppage; no mold skin; complete form; no cavities surface smoothness <= -0.1 mm/cm within contour; no cracks; no pollution (fat, oil dust, etc.) Minimum 1000 Cycles (Slide force 0.4N to 5N)
Durability Bending Torque Drop test UV light exposure Visual inspection Shape and form WP Switch cycles
Minimum moving force of WP witch 40gf (Ensures that the WP switch will not slide while it is inserted to the connector.)
Above technical information is based on industry standard data and tested to be reliable. However, Transcend makes no warranty, either expressed or implied, as to its accuracy and assumes no liability in connection with the use of this product. Transcend reserves the right to make changes in specifications at any time without prior notice.
Transcend Information Inc.
6

▲Up To Search▲

Price & Availability of TS256MSDM

	To Download TS256MSDM Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .